Scosche AU2380B Manuál stáhnout pdf

2006 SCOSCHE INDUSTRIES, INC.

SI 07/06 - AU2380B (3000003)

If you have any further questions, call our toll free technical help line at: 1-800-621-3695x3

AU2380B

2000-UP SELECT AUDI A6

ALL-IN-ONE, SINGLE DIN & DOUBLE-DIN KIT

LIABILITY DISCLAIMER

This instruction booklet is based on carefully documented data and research of automobile dash disassembly, wire

harness/codes and information pertaining to installation of this kit (AU2380B) in 2000-Up Select Audi A6 Vehicles.

Scosche Industries, Inc. can not be held responsible for discrepancies/inconsistencies that may occur due to the

automobile manufacturing changes or options, or damage that may occur in the automobile during the installation of

components while using this booklet.

INTRODUCTION / PRELIMINARY

Thank you for purchasing the Scosche AU2380B Kit. This Kit was manufactured with the highest of quality

standards.

CAUTION: DISCONNECT YOUR VEHICLE'S NEGATIVE BATTERY TERMINAL BEFORE THE

INSTALLATION TO HELP PREVENT ELECTRICAL DAMAGE. WE RECOMMEND THE USE OF A

VOLT/OHM METER OVER A TEST LIGHT TO CHECK WIRING. A TEST LIGHT OR GROUNDED

WIRE PROBE CAN CAUSE DAMAGE TO THE VEHICLE'S COMPUTER AND/OR DIAGNOSTIC

SYSTEMS. AVOID ALL FACTORY AIR BAG WIRING - AIR BAGS CAN ACCIDENTALLY DEPLOY

CAUSING SERIOUS INJURY OR DEATH.

NOTES:

• See your vehicle's instructions for any special tools your installation might require.

• Read all instructions accompanying your car stereo/cassette player for proper wiring and mounting

instructions.

FACTORY WIRING CODES

CAR STEREO CONNECTORS

PROVIDE EASY CONNECTION OF YOUR CAR

STEREO TO FACTORY WIRING HARNESS.

VW03B

2002-UP Volkswagen and BMW

5742 L & R

SINGLE-DIN

ISO BRACKETS

5933

MOUNTING

PANEL

5984

SINGLE-DIN

TRIM RING

6068 L & R

SINGLE-DIN

ISO BRACKETS

5985

SINGLE-DIN

TRIM RING

A. ATTACHING THE POCKET:

Align the pocket to the lower edge of the opening in the

panel. Then slide in, as shown, until pocket snaps into

place. The front of pocket should rest flush to the front

of panel.

POCKET ASSEMBLY

5986

POCKET

RADIO’S

SLEEVE

DIN RADIO

MOUNTING THE RADIO (2 SINGLE DIN / DBL DIN)

A. DIN-ISO / DBL DIN MOUNT:

1. Snap the L/R brackets to the 5933 Kit Panel.

2. Align, position and bolt the aftermarket two IS0-DIN or one

Double DIN head unit to the 6068 brackets. Use hardware

supplied with radio to secure the mounting brackets.

ISO DIN

RADIO

BEND TABS

OUTWARD

MOUNTING THE RADIO

RADIO DISASSEMBLY

Using European radio removal tools (4), slide in to the (4) slots on the factory radio. Pull out, disconnect

and remove

B. DIN INSTALLATION:

1. For DIN mount application, slide into

radio opening.

B. ISO DIN MOUNT:

1. Snap the Left/Right brackets to the 5951

kit panel.

2. Align, position, and bolt the aftermarket

two ISO-DIN.

CAUTION:

REAR SUPPORT AVAILABLE SEPARATELY.

REAR SUPPORTING THE RADIO ADDS TO THE

INSTALLATION’S STRUCTURAL INTEGRITY.

CAUTION:

REAR SUPPORT AVAILABLE SEPARATELY.

REAR SUPPORTING THE RADIO ADDS TO THE

INSTALLATION’S STRUCTURAL INTEGRITY.

2000-UP SELECT AUDI A6 1

Shrnutí obsahu

Strany 1 - 2000-UP SELECT AUDI A6

Komentáře k této Příručce

Žádné komentáře

Scosche AU2380B Manuál

Procházejte online nebo si stáhněte Manuál pro Sady do auta Scosche AU2380B. Scosche AU2380B car kit Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Sady do auta Scosche AU2380B